Brave-beyond5g

Single-Carrier Waveforms for Energy-Efficient Terahertz Communications

Why Waveform Choice Matters in the Terahertz Band

The terahertz band, stretching from roughly 100 GHz to 10 THz, promises enormous bandwidth and, with it, enormous data rates. Yet this promise comes with a physical catch: propagation losses grow sharply with frequency, and the power amplifiers available at sub-THz frequencies are far less efficient than their microwave counterparts. Every decibel counts, and every milliwatt of direct current consumed must be justified by delivered bits.

In this context, waveform design is not a cosmetic detail. It determines the peak-to-average power ratio (PAPR) of the transmitted signal, the complexity of the receiver, and how hard the power amplifier must work to stay linear. Single-carrier waveforms, long dismissed as old-fashioned beside orthogonal frequency-division multiplexing (OFDM), are re-emerging as a serious candidate for energy-efficient terahertz communications.

The Peak-to-Average Power Ratio Penalty of Multicarrier Systems

OFDM divides the available spectrum into many narrow subcarriers, which makes equalization simple and spectrum shaping flexible. The drawback is a high PAPR: the sum of many independent subcarriers occasionally produces large amplitude spikes. To avoid clipping and spectral regrowth, the amplifier must either back off from saturation or be built with substantial extra headroom. Both options waste energy.

Single-carrier transmission avoids this superposition problem. Its envelope is far more stable, so the power amplifier can operate closer to saturation, where it is most efficient. In a band where solid-state amplifiers may deliver only a few percent efficiency to begin with, that difference is decisive.

In the terahertz regime, the waveform with the lowest PAPR is often the waveform with the lowest total energy per bit.

Balancing Rate and Efficiency: Design Levers

Single-carrier waveforms are not a single fixed solution. Designers can trade spectral efficiency against energy efficiency through several levers, including constellation order, pulse shaping, equalization strategy and the use of discrete Fourier transform spreading.

A useful comparison of common options is shown below.

WaveformRelative PAPRReceiver ComplexityEnergy Efficiency
OFDMHighLowLow
SC-FDEModerateModerateHigh
Single-carrier with time-domain equalizationLowHighVery high

The central design choices can be summarized as follows:

  1. Select a constellation that meets the target rate without demanding excessive amplifier back-off.
  2. Apply pulse shaping to constrain out-of-band emission while keeping the envelope stable.
  3. Move equalization to the frequency domain when the channel delay spread is large, accepting modest complexity for major gains.
  4. Exploit DFT spreading to combine the low PAPR of single-carrier signaling with the flexible subcarrier mapping of multicarrier systems.

Energy Efficiency Beyond the Power Amplifier

Energy efficiency in a terahertz link is not only about the transmit amplifier. It also includes analog-to-digital converters, mixers, phase-locked loops and digital baseband processing. Single-carrier schemes can reduce the dynamic range required from converters, since the signal distribution is more concentrated. This allows lower-resolution converters to be used, which cuts both power consumption and cost.

There is also an operational dimension. In short-range sub-THz links, such as wireless backhaul or intra-rack interconnect, the channel is often dominated by a strong line-of-sight path with limited delay spread. Under those conditions, the equalization burden that once made single-carrier systems unattractive becomes modest, while the PAPR advantage remains.

Outlook for Single-Carrier Sub-THz Systems

Single-carrier waveforms will not replace multicarrier solutions everywhere. In highly dispersive scattering environments, OFDM and its variants retain clear advantages. The realistic future is a hybrid one, where the waveform is chosen according to the deployment scenario, the available amplifier technology and the energy budget.

What is certain is that energy efficiency can no longer be an afterthought in terahertz research. As the industry moves beyond 5G toward 6G, the question is not simply how many gigabits per second a link can achieve, but how many joules each of those bits costs. Single-carrier waveform design offers one of the most practical answers to that question.

Latest articles